ELECTRONIC PROJECTS | GADGETS NEWS | LATEST TECHNOLOGY | CONSUMER ELECTRONICS
Showing posts with label Electronic Projects. Show all posts
Showing posts with label Electronic Projects. Show all posts
AUDIO FREQUENCY AMPLIFIER SIMPLE ELECTRONIC PROJECTS COOKBOOK
HOW TO MAKE AUDIO FREQUENCY AMPLIFIER
1. PCB. The plain side is the component side and the soldered side is the track side. Figure 1 shows the track side full size. Make the PCB from the pattern given in Figure 1. Otherwise, build the circuit on a matrix board.
2. Three resistors. Locate the gold or silver band around the resistor, and turn the resistor until this band is to the right. There are three coloured bands at the left-hand end of the resistor. Find the resistor whose colours are YELLOW, VIOLET, RED, and look at the resistor colour code chart which you will find in Chapter 7. From this, you will see that YELLOW indicates the value 4, VIOLET the value 7, and RED the value 2. The first two colours represent real numbers, and the last value is the number of zeros (noughts) which go after the two numbers. So, the value is 47 with two zeros, i.e. 4700 ohms. In this way, the resistor coloured BROWN, GREY, BROWN has a value of 180 ohms, and the last one, BROWN, RED, GREEN, has a value of 1 200 000 ohms. The ohm (often written as the Greek letter omega ( )) is the unit of resistance. If you do not yet feel confident in identifying resistors by their colours, use the Resistor Colour Codes.
3. Four capacitors. The two small ‘beads’ are tantalum capacitors and will be marked 4.7 F or 4 7, with a ‘+’ above one lead. A tubular capacitor with wires coming from each end should be marked 220 F, with one end marked ‘+’ or ‘–’. This is called an axial capacitor because the wires lie on the axis of the cylinder. This is in contrast to the final capacitor, where both wires emerge from the same end. This is a radial capacitor, and will be marked 47 F. Again, one lead will be marked ‘+’ or ‘–’. Capacitors marked like this are said to be polarised, and it is vital that these are placed on the PCB the right way round, so take notice of those signs!
4. Two diodes. These are tiny glass cylinders with a band around one end, and may be marked 1N4148; this is their type number. Like polarised capacitors, they must be put on the PCB the correct way round!
5. Three transistors. One should be a BC548 (or a BC182), the other two should be BC558 (or BC212).
6. One volume control with internal switch.
7. One loudspeaker. This is quite fragile – don’t let anything press against the cone.
8. One PP3 battery clip with red and black leads.
Putting it together
Lay the PCB on a flat, clean surface with the track side downwards. It is
always useful to compare the layout with the circuit diagram, given here in
Figure 3. Although you can’t see it, the D-i-Y Radio sign should be at the
top. Compare the hole positions with those shown in Figure 2. Bend the
resistor wires at right angles to their bodies so that they fit cleanly into the
holes in the PCB. Push each resistor towards the board so that it lies flat on
the board. Then supporting each one, turn the board over and splay out the
wires just enough to prevent the resistor falling out. Then, solder each wire
to its pad on the PCB, and cut off the excess wire. When you have more
confidence, you can cut of the excess wire before soldering; it often makes
a tidier joint.
Now fit the four capacitors. Each must be connected the right way round,
so look at each component, match it up with the diagram of Figure 2, bend
its wires carefully and repeat the soldering process you performed with the
resistors, making sure that the components are close to the board and not up
on stilts! Fit the two diodes the correct way round, and solder then as
quickly as you can – they don’t like to be fried!
Mount the transistors about 5 mm above the PCB. Make sure the correct
transistors are in the correct places, and that the flats on the bodies match
up with those shown in Figure 2.
Mount the volume control so that the spindle comes out from the front of
the board. Use a piece of red insulated wire to the pad marked + on the PCB,
and a black piece to the pad marked –, and solder these to the tags on the
back of the control, as shown in Figure 4. Connect the two leads from the
battery clip to the other tags on the switch; Figure 4 will help you. Finally,
use two pieces of insulated wire about 100 mm long, twisted together, to
connect the loudspeaker to the PCB.
DIGITAL CLOCK WITH SECONDS AND ALARM TIME DISPLAY SIMPLE ELECTRONICS PROJECT
THIS IS FOR A SIMPLE DIGITAL CLOCK WITH SECONDS AND ALARM TIME DISPLAY
Typical digital clocks using clock chips MM5387/MM5402 and MM5369 show normal time in only
hours and minutes, and seconds or alarm time is visible only after pressing a pusht o on switch. Here’s a digital clock using the same IC (MM5387) that shows normal time in hours, minutes, and seconds and alarm time simultaneously. For this, ten 7-segment LED displays and a few extra ICs and some discrete components are needed.
PARTS LIST
Semiconductors:
IC1, IC5 - CD4017BE decade counter/
divider
IC2 - NE555 timer
IC3 - MM5387 clock chip
IC4 - CD4060 14-stage binary
counter
T1-T5 - BC547 npn transistor
D1-D6 - 1N4001 rectifier diode
D7, D8 - 1N4148 fast switching diode
Resistors (all ¼-watt, ±5% carbon,
unless stated otherwise):
R1 - 10-kilo-ohm
R2 - 150-ohm
R3-R7 - 15-kilo-ohm
R8 - 3.3-mega-ohm
Capacitors:
C1 - 0 .01μF ceramic disk
C2 - 4.7μF, 16V electrolytic
C3 - 1000μF, 16V electrolytic
C4 - 470μF, 16V electrolytic
C5-C7 - 0.22μF ceramic disk
C8, C9 - 47pF ceramic disk
Miscellaneous:
XTAL - 4.9152MHz crystal
LED1, LED2 - 5mm dia. red LED
DIS1-DIS10 - LT543 common-cathode
7-segment display
S1 - SPDT switch
S2-S7 - Push-to-on tactile switch
X - 230V AC primary to 4.5V-0-
4.5V secondary, 500mA
transformer
- 9V PP3 battery
Schematics
CAR SECURITY SYSTEM WITH REMOTE CONTROL SIMPLE ELECTRONIC PROJECTS
Here is an inexpensive electronic car security system with remote control that uses readily available, low-cost components. The gadget comprises a base unit, which remains fitted inside the vehicle, and a remote control handset for activating/deactivating the base unit. The base unit, in enabled state, can be used to set off an alarm device when an unauthorised person tries to gain access to the vehicle.
Remote control handset
The remote control handset is used to switch on/off the base unit installed inside the vehicle.
Base Unit
SIMPLE LOW POWER AUDIO AMPLIFIER BASIC ELECTRONIC PROJECTS
The small-signal amplifier is generally referred to as a voltage amplifier because it usually converts a small input voltage into a much larger output voltage. The audio power amplifier works on the basic
principle of converting low-power audio signal to a suitable level to be delivered to the load.
This low-power amplifier circuit is useful for the amplification of sound from small-signal devices such as mobile phones, laptops or desktops.
Circuit and working As shown in Fig. 1, this circuit is built around a step-down transformer (X1), bridge rectifier BR1, regulators 7809 (IC1) and 7909 (IC2), dual op-amp TL072 (IC3), low-power amplifier LM386 (IC4) and some other components.
The circuit can be divided into two sections—dual power supply section and amplifier section. The dual power supply section is built around step-down transformer X1 (230V ac primary to 12V-0-12V, 1A secondary) and two voltage regulators 7809 and 7909.
IC 7809 is a positive voltage regulator, while 7909 is a negative voltage regulator. Diodes D1 and D2 are used to protect IC1 and IC2 against reverse voltages from capacitors connected to the regulators. These regulators provide ±9V regulated output for the operation of the circuit.
Use suitable heat sinks with the regulator ICs because they get hot during operation. In case of overheating, there is provision for a thermal shutdown.
The amplifier section is built around TL072 (IC3) and a low-power amplifier LM386. The op-amp A1 of IC3 operates as a low-noise preamplifier. Capacitor C8 is used in order to pass low frequency. The op-amp A2 of IC3 operates as a low-pass filter. For changing the cut-off frequency, you have to change the values of capacitors C11 and C12.
LM386 is a low-power amplifier IC with built-in biasing and inputs that are referred to the ground. It has a gain of 20 and can drive a speaker of 8-ohm impedance.
Parts List
Semiconductors:
IC1 - 7809, +9V regulator
IC2 - 7909, -9V regulator
IC3 - TL072 dual op-amp
IC4 - LM386 low power audio
amplifier
BR1 - 1A bridge rectifier
D1, D2 - 1N4007 rectifier diode
Resistors (all 1/4-watt, ±5% carbon):
R1 - 1-kilo-ohm
R2 - 10-kilo-ohm
R3 - 2.2-kilo-ohm
R4 - 47-kilo-ohm
R5-R7 - 33-kilo-ohm
R8 - 56-kilo-ohm
R9 - 3.3-ohm
VR1 - 10-kilo-ohm potentiometer
Capacitors:
C1, C3 - 1000μF, 35V electrolytic
C2, C4 - 0.33μF ceramic disk
C5, C6 - 1μF, 25V electrolytic
C7, C14 - 220μF, 25V electrolytic
C8 - 4.7μF, 25V electrolytic
C9, C10, C13 - 0.1μF ceramic disk
C11, C12 - 0.01μF ceramic disk
Miscellaneous:
LS1 - 8-ohm, 0.5W speaker
RCA1 - RCA socket
X1 - 230V AC primary to
12V-0-12V, 1A secondary
transformer
- 8-pin IC bases for ICs
- Heat sinks for regulators
RAIN ALARM SIMPLE ELECTRONIC PROJECT
Schematic diagram for rain alarm.
GIVES BEEP WHEN WATER IS IN CONTACT WITH THE WIRE
Water is a conductor of electricity. When water is in contact with the probe then there is a flow of current which reaches to the base of Q1. Transistor Q1 is a NPN transistor which conducts. With the conduction of Q1 electron reaches to Q2 which s a PNP transistor .
Q2 also conducts and current flows through the speaker. In aspeaker there is inductive coil which causes motion in one direction and also produce induce current which is in opposite direction to the flow of current this induce current in the form of pulse flows through a capacitor, resistance and switches off Q1 and relax .
This process repeats again and again till probe is in contact with water or we can say there is a oscillation in the circuit thus speaker diaphragm vibrates and gives a tone. Frequency of the circuit depends on the value of Speaker Coil impendance, Capacitor and Resistance Value.
AUTOMATIC WATER PUMP CONTROLLER CIRCUIT ELECTRONIC PROJECTS
This is a simple schematic diagram of automatic water pump controller.
The circuit of a water pump controller, as shown in the diagrag, comprises three npn transistors, all connected as emitter followers to present high input and low output impedance. Gate N1 of the quad NAND gate iC is connected as an inverter, while two other NAND gates N2 and N4 form a set-reset flip-flop controlled by outputs of NAND gate N1 and pole voltage of relay Rl2.
The tank has a reference probe C, which is directly connected to 12V supply, while probe a represents the lower limit of liquid (any conductive liquid including normal drinking water) level. if liquid level falls below this level the pump motor must start and remain on until the liquid touches the upper probe B.
When the liquid level falls below probe a level, transistor T1 is cut off and hence pin 13 of gate N4 (via N/C contact of relay Rl2) is at ground level. The output pin 11 of gate a therefore goes high.
Transistor T3 conducts to energise relay Rl1 and the pump motor is switched on through its contacts. Once water touches probe A (but not the upper limit probe B), relay RL2 energises because of forward biasing of transistor T1, whereby pin 13 of gate N4 goes high.
But its other input pin 12 is low as transistor T2 is not conducting. hence input to gate N1 is low and the logic output of gate N2 is low.
PartS LiSt
IC1 - CD4011 - quad 2-input NAND gate
T1- T3 - BC547 - npn transistor
D1, D2 - 1N4001 - rectifier diode
R1, R2, R6 - 1-kilo-ohm - resistor, 0.25W
R3, R5 - 47-kilo-ohm - resistor, 0.25W
R4 - 10-kilo-ohm - resistor, 0.25W
Rl1, Rl2 - 12V, 1 C/O - relay with 1a contact rating
- probes - 3 metal probes on insulating rod
- 12 V battery
Subscribe to:
Posts (Atom)





